INSTALLATION INSTRUCTIONS FOR
3-RAM TILT/TRIM SYSTEMS

WORKS ON:

Mercury outboards 135 to 300 hp.

 
Yamaha (plus new SHO) outboards 115 to 350 hp.


Honda outboards 90 hp to 300 hp.

 

Evinrude outboards 150 to 300 hp, except Generation 2.


Johnson four-stroke outboards 150 to 300 hp, V6 4-stroke.


Suzuki four-stroke outboards DF140 to DF350 hp.

 

Tohatsu outboards 115 to 250 hp.


Works on virtually any boat!

1. Trim outboard to up position.

2. On trim/tilt switch side, simply slide m-y wedge over trim/tilt piston rod of lower unit .

3. Slide completely down. m-y wedge will position and self-center.

4. Trim outboard down until the rubber begins to compress.

5. To remove m-y wedge simply trim outboard to up position and remove.

6. Store m-y wedge in any boat compartment for convenience.

 

F300–F350 V-8 models need 2 m-y wedge units, Port and Starboard.

 

NOTE: We recommend that you rotate m-y wedge 1/4 to 1/2 turn after each use. This helps even the compression of the EPDM Rubber on the unit.

Install on trim/tilt switch side, normally Starboard side of Mercury, Honda, Johnson 4-stroke, Evinrude, Tohatsu outboards.

Mercury fits on starboard side. Installs on trim/tilt piston. Self centers. Snug down to secure. Correct trailering height shown. No need to hold on to anything!

Click Here for a PDF of the Mercury, Honda, Evinrude, Johnson, Tohatsu Instructions.

 

Click Here for a PDF of the Yamaha, Suzuki Instructions.

Install on trim/tilt switch side, normally Port side of Yamaha, Suzuki outboards.

Note: On Yamaha and Suzuki the trim/tilt switch may be on the Starboard side. If there is a grease zerk where the m-y wedge meets the swivel bracket, the m-y wedge must go on the side opposite the grease zerk.

Yamaha fits on port side. Installs on trim/tilt piston. Self centers. Snug down to secure.

Lower until starboard piston retracts 1/4 inch to 1/2 inch to secure. Correct trailering height shown.

 

 

WORKS ON:

Mercury 15 to 200 hp 4-stroke with single-ram trim/tilt

 

Yamaha (9 to 90 hp and new F115LB)  with single-ram trim/tilt

 

Honda  with single-ram trim/tilt

 

Suzuki  with single-ram trim/tilt

 

Evinrude  with single-ram trim/tilt

 

Johnson  with single-ram trim/tilt

 

Tohatsu  with single-ram trim/tilt

 

Kicker motors with power tilt systems.

1. Trim outboard to up position.

2. Simply push the Universal m-y wedge on the power-tilt rod and it will pop or click into place.

3. Trim outboard down until the rubber begins to compress.

4. To remove Universal m-y wedge simply trim outboard to up position and remove.

5. Store Universal m-y wedge in any boat compartment for convenience.

 

NOTE: The Universal m-y wedge can be cut to size, if your outboard sits too high or you have problems with tilting your motor high enough to install the unit. Simply cut the Universal m-y wedge using a miter or hack saw. You normally don't need to cut off more than an inch.

INSTALLATION INSTRUCTIONS FOR SINGLE-RAM POWER TILT SYSTEMS

Mercury Verado 6-cylinders use two Universal m-y wedge units.

© 2018  Raveling OutdoorS   |   P.O. Box 343   |   Longville, MN 56655